Flight Gear Info Articles

Oxygen Mask Fittings and CRU Blocks Like anything else in military aviation, there are many different items doing a similar job, but each one is specialized for specific applications. Below we will discuss 3 types of "oxygen mask connectors" and 2 types of "oxygen blocks" as used primarily by the Air Force. We have Oxygen Mask Hose Fittings and CRU Blocks available for sale:Oxygen Mask Hose Fittings • CRU Chest Mounted Regulators • CRU Harness Mounting Plate Oxygen mask connectors as shown- Top: 2 Pin Friction Quick Disconnect fitting. Used in "non-tactical" aircraft or those without ejection seats. There have been many different styles and colors. For instance, early ones are longer than the one shown and aluminum silver in color- later ones are black and typically shorter. You will see several different colored gasket seals, the one shown is red. Used with MBU-5/P and MBU-12/P oxygen masks in aircraft like the F-111 Aardvark. Middle: The next fitting is a 3 Pin Quick Disconnect fitting. These are for use in ejection seat aircraft that utilize a bailout bottle and therefore a CRU-60 or CRU-94 oxygen block (see more info below). This is used with the MBU-5/P, MBU-12/P, or MBU-20/P oxygen mask and their variants in aircraft like the A/F F-4 Phantom, F-15 Eagle, F-16 Falcon. Bottom: The MC-3A connector was used in quantity by the Navy and Air Force from the end of WW2 the 1960s. They are even used today on a special MBU-12/P variant in aircraft like the Marine Corps OV-1 Bronco. You can find this fitting on MS22001s, A-14s, and more. The offset elbow is for bailout bottle attachment. The actual attachment part is the same as the 2 Pin Friction fitting. There is a cloth loop that snaps shut to secure the heavy connector so it does not hit the pilot during ejection. When a crewmember ejects, they need to be supplied oxygen in case egress from the aircraft occurs at over 10,000 feet AGL. The modern ejection seats have emergency o2 stored oxygen bottles "Bail-Out Bottle" built into the seat. The crewmember receives the oxygen supply during regular flight from the aircraft o2 system (the Air Force has the regulator built into the aircraft system, the Navy uses crew-mounted regulators [CRU-79/P, CRU-88/P] see the MBU-12/P vs. MBU-14/P article. The Air Force uses oxygen blocks which have "ports" for various fittings. The CRU-60/P, seen here attached to the PCU-15ejection torso harness (F-4 Phantom, F-15 Eagle). The CRU block (60/P or 94/P) attaches securely to the PCU harness via the metal CRU Bracket, seen at right. The MBU-12/P or 5/P oxygen mask attaches to the CRU-60/P by the 3 Pin Quick Disconnect fitting. The hose from the emergency bottle in the ejection seat attaches to the Bail Out Bottle elbow. The aircraft oxygen hose hooks into the friction fitting at the bottom of the CRU-60/P. This "friction" fitting requires 5 pounds of pull to disconnect- Upon ejection, the aircraft oxygen hose separates from the CRU-60 and the crewmember breathes from the bailout bottle. The Combat Edge CRU-94/P oxygen block is seen here attached via the CRU Bracket to the PCU-15A/P ejection torso harness (used on the F-16 Fighting Falcon). The MBU-20/P Combat Edge (CE) oxygen mask attaches to the CRU-94/P by the 3 Pin Quick Disconnect fitting, like the masks do above to the CRU-60/P. The only difference between the CRU-60 and the CRU-94 is the addition of one extra port for the CSU-17/P Counter Pressure Vest. It plugs into the 94/P with a 4 Pin Quick Disconnect fitting. The other bail-out bottle & aircraft friction fitting works the same as on the CRU-60/P.

Flight Gear Info Articles

Oxygen Mask Fittings and CRU Blocks

Flight Helmet Oxygen Masks and Bayonet Receivers

Recent Posts

Flight Gear Info Articles

Categories

Archives